Dual Low-Noise JFET Opamp TL072
The JFET-input operational amplifiers in the TL07x series are designed as low-noise versions of the TL08x series amplifiers with low input bias and offset currents and fast slew rate.
Karnaugh Map Minimizer - Refactoring Code
A tool for developers of small digital devices and radio amateurs, for those who is familiar with Boolean algebra and Karnaugh Map optimization method, best suits for electrical engineering students.
Karnaugh Minimizer - Refactoring Code
FireFly WSN Platform
The main Firefly board uses an Atmel ATmega1281 8-bit micro-controller with 8KB of RAM and 128KB of ROM along with Chipcon’s CC2420 IEEE 802.15.4 standard-compliant radio transceiver for communication. The maximum packet size supported by 802.15.4 is 128 bytes and the maximum raw data rate is 250Kbps.
Induction Heating - Cooker Project
Single plate induction cooker demonstration board Uses ST7LITE09 and STGW40NC60WD (40 A, W series).
The design is entirely controlled by a simple ST7FLITE09Y0 8-bit microcontroller, which provides the PWM driving signals, communicates information to the user interface, and drives the fan and relay control to the plate feedback.
With Single Voltage Flash Memory, Data Eeprom, Adc, Timers, Spi Active - ST7LITE09Y0 8-Bit Mcu
ViPEC Network Analyzer
ViPEC is a powerful tool for the analysis of high frequency, linear electrical networks. It takes a schematic description of the electrical network and performs a linear analysis in the frequency domain.
The output is in the form of port parameters (S, Y or Z) with results presented on a user defined grid, Smithchart or table. It can also be used to compute other characteristics like stability factors and group delay.
IMU - Accelerometers and Gyroscopes
Accelerometers and Gyroscopes as well as combination IMU devices (Inertial Measurement Unit). The ADXL345 from Analog Devices is a small, thin, low power, 3-axis accelerometer with high resolution 13-bit measurement at up to ±16 g.
Earthing Practice and Power Quality
"Earth leakage currents arise mainly from the EMC filters built into electronic equipment with switched mode power supplies. Standards limit the leakage current from non-fixed equipment (i.e. equipment that plugs into a standard socket outlet) to less than 3.5 mA. When a lot of electronic equipment is in use, the total leakage current in the protective conductor can become significant."
SCADA - Supervisory Control and Data Acquisition
A Closed loop control system has a Sensor-Controller-Actuator. The Bimetal Thermostat has all the three in the Bimetal itself. The Sensor, the Relay Contact and the Intelligence. This is Process Control when implemented to control the temperature in a Bakery Oven.
This leads us to Sensors-Transmitter-Controller-Outputs-Actuators. Where each is an independent electronic/electrical component of an entire Process Control system. The Process could be Temperature, Pressure, Speed, or Level.
CAN Controller Area Network in Automation
CAN (Controller Area Network) is a serial bus system, which was originally developed for automotive applications in the early 1980's. The CAN protocol was internationally standardized in 1993 as ISO 11898-1 and comprises the data link layer of the seven layer ISO/OSI reference model.
CAN Controller Area Network in Automation
CANopen is a CAN-based higher layer protocol. It was developed as a standardized embedded network with highly flexible configuration capabilities.
LaTeX Equation Editor - Equation Maths
Writing Mathematics on the Internet. Witing equations is difficult in a doc, they have to be font independent, that implies images. Webapps do it well.
LyX combines the power and flexibility of TeX/LaTeX with the ease of use of a graphical interface. This results in world-class support for creation of mathematical content (via a fully integrated equation editor) and structured documents like academic articles, theses, and books.
CACHE Teaching Resource Center
Provides substantial material on various Industrial Automation and Chemical Engineering topics. Pages of interest Material Science, Thermodynamics, Process and Product Design and Fluid Mechanics.
CACHE Teaching Resource Center
Here are reference areas for Industrial Automation and Process Control Instrumentation Students/Teachers.
Pages
